公司新聞
冷再生機機械的保養注意事項
來源：http://www.baoxiaomei.cn/ 日期：2023-06-28
一、清洗外表
1、 Cleaning the exterior
1、冷再生機租賃在施工過程中會有大量的灰塵落到再生機的表面，包括施工中沾污的油跡等污染物，影響外觀事小，更為嚴重的是成為腐蝕的誘發因素。
1. During the construction process of the cold regeneration machine, a large amount of dust will fall onto the surface of the regeneration machine, including pollutants such as oil stains during construction, which have a small impact on the appearance and, more seriously, become an inducing factor for corrosion.
1.清洗工程機械的柴油機、底盤、工作裝置的外表,除垢、除油保持再生機的外觀整潔。
1. Clean the exterior of the diesel engine, chassis, and working equipment of the construction machinery, remove dirt and oil, and keep the appearance of the regeneration engine clean.
2.清洗時嚴禁用高壓、高溫的水槍來沖洗防水要求較高的部位（特別是電器部分），以免造成電器部分的損壞。
2. It is strictly prohibited to use high-pressure and high-temperature water guns to wash parts with high waterproof requirements (especially electrical parts) during cleaning, in order to avoid damage to the electrical parts.
清洗外表，是工程機械冬季保養要點之一。
Cleaning the exterior is one of the key points for winter maintenance of construction machinery.
二、保養轉子及其罩殼和滑靴
2、 Maintain the rotor and its casing and shoes
1.檢查轉子是否有水泥結垢等，及時清理灰塵，對需要割除、焊接的刀具及時更換；
1. Check if there is cement scaling on the rotor, clean the dust in a timely manner, and replace the cutting tools that need to be cut or welded in a timely manner;
2.清理轉子罩殼上的灰塵，并在施工結束收車時將轉子罩殼墊起地面5-10公分，防止雨雪的浸蝕；
2. Clean the dust on the rotor casing and pad the rotor casing 5-10 cm above the ground at the end of construction to prevent erosion by rain and snow;
3.檢查滑靴，對已經磨損的滑靴部分進行補焊，螺紋處應涂抹黃油防銹。
3. Check the sliding shoes, repair welding the worn parts of the sliding shoes, and apply butter to the threads for rust prevention.
三、減速機齒輪油的更換方式
3、 Replacement method of reducer Gear oil
準備事項：
Preparation:
1、場地:要求無塵硬化路面，面積應在200平方米左右，盡量是庫房，但要有足夠25噸的吊車的工作高度和半徑。
1. Site: Dust free and hardened road surface is required, with an area of about 200 square meters. It should be a warehouse as much as possible, but there should be a sufficient working height and radius for a 25 ton crane.
2、設施：25噸吊車一臺（20噸也可以）。
2. Facilities: One 25 ton crane (20 tons is also acceptable).
3、配件：進口美孚齒輪油9升、衛生紙10卷、塑料帶20個、廢油桶2個、緊固膠262/340一支、密封膠587一支、黃油一袋，細線繩20米、12*45的帶母螺栓30套、4*30開口銷10個。
3. Accessories: 9 liters of imported Mobil Gear oil, 10 rolls of toilet paper, 20 plastic belts, 2 waste oil drums, a piece of fastening glue 262/340, a piece of sealant 587, a bag of butter, 20 meters of string, 30 sets of 12 * 45 bolts with nuts, and 10 4 * 30 cotter pins.
4、工具：10、16、18、19、21、22、24、30套筒和扳手至少一套、快速扳手及長、短接桿各一、加力桿一根、30的輪胎扳手、10毫米的內六角扳手、55的活口扳手兩把、小號活口扳手一把、小號的老虎鉗一把、手鉗一把、一字螺絲刀一把、大小錘頭各一、撬棍兩根，配備氣動扳手和氣泵，能提高工作效率。
4. Tools: at least one set of 10, 16, 18, 19, 21, 22, 24, 30 sockets and wrenches, one quick wrench, one long and short connecting rod, one booster rod, 30 tire wrench, 10 mm Hex key, two 55 open-end wrenches, one small open-end wrench, one small Lineman's pliers, one hand wrench, one slotted screwdriver, one large and small hammer head, two crowbars, and equipped with Impact wrench and air pump, which can improve working efficiency.
以上是關于冷再生機機械的保養注意事項，大家如有更多的想法和意見歡迎洽談合作，本公司http://www.baoxiaomei.cn租賃冷再生機，銑刨機出租，攤鋪機租賃，出租冷再生機等，常年對外出租各種大型機械！
The above are the maintenance precautions for the cold regeneration machine machinery. If you have more ideas and opinions, please feel free to negotiate cooperation. Our company http://www.baoxiaomei.cn Rental of cold regeneration machines, milling machines, paving machines, rental of cold regeneration vitality, and long-term rental of various large machinery to the public!
公司地址：濟南市槐蔭區經一路273號群盛華城2號樓1-404
公司名稱：山東途暢路橋工程有限公司 
備案號：